Metal detector
This article is licensed under theGNU Free Documentation License.It uses material from the Wikipedia article 'Metal detector' (click for full Wikipedia text) 'Metal detectors ' use electromagnetic induction to detect metal.
The first detectors
Metal detectors have been around for much longer than most people realise. Towards the end of the 19th century, many scientists and engineers used their growing knowledge of electrical theory in an attempt to devise a machine which would pinpoint metal. The use of such a device to find ore-bearing rocks would give a huge advantage to any miner who employed it. The German physicist Heinrich William Dove invented the induction balance system, which was incorporated into metal detectors a hundred years later. Early machines were crude and used a lot of battery power, and only worked to a very limited degree. The Scottish physicist, Alexander Graham Bell, used such a device to attempt to locate a bullet lodged in the back of American President James Garfield in 1881.
Modern developments
The modern development of the metal detector began in the 1930's. Gerhard Fischer had developed a system of radio direction-finding, which was to be used for accurate navigation. The system worked extremely well, but Dr Fisher noticed that there were anomalies in areas where the terrain contained ore-bearing rocks. He reasoned that if a radio beam could be distorted by metal, then it should be possible to design a machine which would detect metal, using a search coil resonating at a radio frequency. In 1937, he applied for, and was granted, the first patent for a metal detector. His designs were soon put to the test in a practical way, as they were used as mine detectors during the Second World War. They were heavy, ran on vacuum tubes, and needed separate battery packs - but they worked. After the war, there were plenty of surplus mine detectors on the market; they were bought up by relic hunters who used them for fun and for profit. The hobby of metal detecting had been born.
Further refinements
Many manufacturers of these new devices brought their own ideas to the market. Whites Electronics of California began in the 50's by building a machine called the Oremaster Geiger Counter, and are still at the leading edge of detector innovation today. Another leader in detector technology was Charles Garrett, who pioneered the BFO (Beat Frequency Oscillator) machine, and whose company is still one of the world leaders in design. With the invention and development of the transistor in the 50's and 60's, metal detector manufacturers and designers made smaller lighter machines with improved circuitry, running on small battery packs. The metal detector was reduced to a size that even a child could use - and use them they did. Fabulous finds were made; prehistoric gold ornaments, chests of Roman coins, jewelled daggers - all types of metal artifacts were coming out of the ground. Suddenly, there was a huge requirement for those early electronic magic wands which might make a man rich overnight. Companies sprang up all over the USA and Britain who wished to supply the growing demand. Larger portable metal detectors are used by archaeologists and treasure hunters to locate metallic items, such as jewelry, coins, bullets, and other various Artifact (archaeology) buried shallowly underground.
Discriminators
Technological changes were taking place at a rapid rate too, and very few of the smaller companies managed to stay in competition with the big outfits. GOLDAK, METROTECH, IGWT, TEC, and, quite recently, ARADO ceased production of hobby machines. Some devotees of metal detecting still treasure their Arado machines, which had a reputation for being difficult to set up, but were reputed to be the deepest-seeking hobby detectors ever made. The biggest technical change in detectors was the development of the induction-balance system, where two coils are set up in an electrical equilibrium to produce a 'null' or zero balance. Introducing metal to the vicinity of the coils caused them to unbalance, producing a change of tone in the machine's speaker. Scientists had long known that every metal has a specific response to stimulation by alternating current. Each metal produces a time lag or 'phase angle' in its induced current, in relation to the drive current. This meant that detectors could now be set up to ignore unwanted phase angles, and respond positively only to desired metals. But there was also a downside to the development of the 'discriminator' detectors. Introducing discrimination always had the effect of reducing the sensitivity of the machine, so it was less able to find deep objects. In addition, there was the fact that some desirable metals were quite near the area of unwanted metals, such as iron. Gold, particularly in alloy form, was quite close to tinfoil in the overall spectrum, so the discrimination control had to be used carefully. The price to be paid for setting up a detector to ignore iron and tinfoil was the certainty that, sooner or later, the user would scan over, and ignore, a valuable find - perhaps a diamond engagement ring on a beach.
New coil designs
Coil designers also tried out innovative designs. The original Induction Balance coil system consisted of two identical coils placed on top of one another. Compass Electronics produced a new design; the two coils were made in a D shape, and were mounted back-to-back to form a circle. This system was widely used in the 70's, and both concentric and D type (or Widescan as they became known) had their fans. Another development was the invention of detectors which could cancel out the effect of mineralisation in the ground. This gave greater depth, but was a non-discriminate mode. It worked best at lower frequencies than those used before, and frequencies of 3 to 20 KHZ were found to produce the best results. Many detectors in the 70's had a switch which enabled the user to switch between the discriminate mode and the non-discriminate mode. Later developments switched electronically between both modes. The development of the Induction Balance detector would ultimately result in the Motion detector, which constantly checked and balanced the background mineralistaion.
Pulse induction
At the same time, developers were looking at using a completely different type of technology in metal detectors. This was the process known as Pulse Induction. Unlike the Beat Frequency Oscillator or the Induction Balance machines which both used a uniform alternating current at a low radio frequency, the pulse induction machine simply fired a high-voltage pulse of signal into the ground. In the absence of metal, the 'spike' decayed at a uniform rate, and the time it took to fall to zero volts could be accurately measured. However, if metal was present when the machine fired, a small current would flow in the metal, and the time for the voltage to drop to zero would be increased. These time differences were minute, but the improvement in electronics made it possible to measure them accurately and identify the presence of metal at a reasonable distance. These new machines had one major advantage: they were completely impervious to the effects of mineralisation, and rings and other jewellery could now be located even under highly-mineralised 'black sand'. They had one major disadvantage too: there was no way to incorporate discrimination into a Pulse induction detector. At least, that was the perceived wisdom of scientists and engineers until Eric Foster, who had run Location Technology in Ireland for many years, started a new company in Britain and produced the Goldscan, the first Pulse Induction detector which had the apparent ability to differentiate between metals. This was a new type of 'junk eliminator' circuit, which relied on the size of the target as well as its metallic response to give a control that would show positive for a gold ring and negative for a copper coin. Its ability to differentiate between non-ferrous metals was not an exact science, but gave unparalleled depth on mineralised soil or sand. Pulse Induction detectors are now widely used in the construction industry; the Whites PI-150 is an industrial machine which can detect large objects to 10 feet, using a 12 or 15 inch coil.
Future detectors
Metal detectors have come a long way, from the simple one-coil BFO, to today's sophisticated machines. Modern top models are fully computerised, using microchip technology to allow the user to set sensitivity, discrimination, track speed, threshold volume, notch filters, etc, and hold these parameters in memory for future use. Compared to just a decade ago, detectors are lighter, deeper-seeking, use less battery power, and discriminate better. We can expect to see more improvements as designers continue to apply the latest Electronics and Computer technologies to the task of making ever better metal detectors.
Metal detectors and archaeology
The use of metal detectors to search for archaeological finds is practised both by archaeologists and hobbyists. In some European countries including France, Italy and Sweden the use of a metal detector is forbidden by law, unless one has special permission. This is intended to protect archaeological sites but rarely means that illicit metal detecting ('nighthawking') does not take place and has the effect that new sites found by metal detector are never publicised or investigation fully. Instead, they are slowly plundered for their metal items, disturbing the stratigraphy and forcing the Artifact (archaeology)s on to the Black Market, never to be seen again. One of the main causes of driving the hobby underground is the inability of some within the detectorist world to come to terms with fellow detectorists who fail to record their finds for future generations. In the United Kingdom metal detecting is legal provided permission is granted by the landowner, and the area is not a Scheduled Ancient Monument or covered by elements of the Countryside Stewardship Scheme. In England and Wales voluntary reporting of finds to the Portable Antiquities Scheme is encouraged. This scheme has critics however, including some archaeologists and metal detectorists. Countries with no restrictions or methods to deal with new finds in place are in danger of sites being regularly raided and their contents sold on without the information they provide ever being known. However, there are some responsible metal detectorists in unrestricted nations who contact archaeologists when they find artefacts, and who never dig. They try to benefit archaeology by finding artefacts for scientists. Archaeologists use metal detectors to scan their spoil heaps and also to examine wide areas such as battlefield where surface scatters of metal objects may be all that survives.
UK Finds Databases
- UK Detector Finds Database
- Portable Antiquities Scheme
See also
External links
Explain Metal Detectors 
Accurate Locators - Original Metal Detectors Website
